Use a tapered or QD bushing from Ever-Power with sheaves, pulleys, sprockets and many other power tranny applications. Flanged quick-disconnect bushings include a completely split design to greatly help provide easy set up and disassembly. A tapered bushing with straight edges uses an interior screw to greatly help drive the bushing in to the shaft, while a split taper has a flange and a key on the bushing to greatly help provide more drive.
L – Space required to tighten bushing or loosen to remove hub with puller using brief hex key.
M – Space required to remove bushing using screws as jackscrews – brief hex key – no puller reuired.
Listed required hub diameter can be for reference only. Severe conditions may necessitate bigger hub and in some instances a slightly smaller hub could be satisfactory. Inquire about specific application.
We are able to also supply special bushings made of other machinable materials. Please inquire
External key on most sizes for positive drive and better torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep concentric bores
Available in inch, metric, and spline bores. Bore range from 3/8″ to 10″
Gates Taper-Lock bushings are used to install pulleys, sprockets and sheaves on shafts. The long lasting stainless steel construction is ideal for meals and beverage applications or where non-corrosive sprockets are needed to prevent rust.
This Taper-Lock bushing is ideal for use with same-type sheaves, sprockets, and pulleys in power transmission applications that require synchronous rotation. The carbon metal bushing provides power and resistance to use and includes installation bolts and washers. Taper-Lock sheaves, sprockets, and pulleys (not really included) can be found in a number of outside diameters to match this Taper-Lock bushing, allowing the complete selection of the amount of drive teeth or grooves. This bushing is certainly ideal for use in a wide selection of mechanical and electronic adjustable drives, including auto and printing industries.

Plain bearings provide low-friction sliding contact for relative motion between parts of a machine. They will be the simplest type of bearing, without rolling elements, and there are three basic types of plain bearings: radial simple bearings (also called sleeve bearings or bushings) to support rotating or reciprocating shafts, thrust bearings (also called washers) to aid axial loads on shafts, and linear bearings to support and guide the motion of parts in a directly range. Flanged sleeve bearings have a flange using one end to aid axial loads. Spherical plain bearings are radial bearings that enable angular misalignment of the shaft. Plain bearings are produced from durable, low-friction components such as sintered or cast bronze alloys, plastic material, or a combination of a metal shell and a plastic material bearing surface. They could be lubricated externally or by a lubricant embedded in the bearing materials. Plain bearings are used in automobiles, structure and mining devices, textile manufacturing devices, and robotics, amongst others.
The maximum bore is supplied with a standard ANSI/AGMA 9002-B04 or ISO 286-2 keyway.
Taper Lock Bushing installation screws could be either ” (UNC) or metric (BSW) and care should be taken to select the proper hub part quantity.
Taper Lock Busings certainly are a taper bore bushing china product of Baldor Dodge and so are not included with Lovejoy coupling hubs.
Optimum bores size and torque capacities are per Dodge specifications and Lovejoy isn’t responsible for the accuracy of any of the values listed in accordance with bore size and torque capacity.
Split Taper Bushings. Split-taper bushings are used to attach sprockets, pulleys, and couplings onto shafts. They have a tapered, split body that locks the bushing down onto the shaft, prevents it from slipping during operation, and transfers more torque.
All reborable bushings are stocked
without sawsplit to facilitatere-machining.
Sawsplit must be made in bushing to permit it to compress for proper gripping of the shaft.
Adapters for TAPER-LOCK bushings are recommended for use where it is more convenient to straight bore than to drill, tap and taper bore hubs to accommodate bushings. The adapter is definitely a gray iron, taper-bored sleeve whichfits into the directly bore of a hub. The bushing simply fits inside the adapter which can be tapped for the bushing screws. When tightening the locking screws, adapter is usually expanded against the hub bore contracting the bushing tightly upon the shaft.
Ever-Power offers an comprehensive range of energy absorbing elastomeric isolators that limit the tranny of structure-borne vibration and impacts. Our items are made for simple use and a multitude of orientations in compression, shear and slanted angle loading. While economical, these products are made from quality rubber, silicone, Neoprene and steel components that enable support for the proper amount of load for each application. Filter through our in-depth product listing of elastomeric products including bottom mounts, cup mounts, bumpers, bushings and grommets to get the right remedy for your application.
Make use of a tapered or QD bushing from Ever-Power with sheaves, pulleys, sprockets and several other power transmission applications. Flanged quick-disconnect bushings include a completely split design to greatly help provide easy set up and disassembly. A tapered bushing with straight edges uses an internal screw to greatly help drive the bushing into the shaft, while a split taper includes a flange and an integral on the bushing to help provide more drive.
L – Space required to tighten bushing or loosen to eliminate hub with puller using brief hex key.
M – Space necessary to remove bushing using screws as jackscrews – brief hex key – no puller reuired.
Listed required hub diameter is usually for reference only. Severe conditions may necessitate bigger hub and in some instances a slightly smaller sized hub could be satisfactory. Inquire about specific application.
We can also supply unique bushings made of other machinable materials. Please inquire
External key on most sizes for positive drive and better torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep concentric bores
Available in “, metric, and spline bores. Bore range between 3/8″ to 10”
Gates Taper-Lock bushings are used to attach pulleys, sprockets and sheaves on shafts. The durable stainless steel construction is perfect for meals and beverage applications or where non-corrosive sprockets are had a need to prevent rust.
This Taper-Lock bushing is ideal for use with same-type sheaves, sprockets, and pulleys in power transmission applications that require synchronous rotation. The carbon metal bushing provides power and resistance to use and includes mounting bolts and washers. Taper-Lock sheaves, sprockets, and pulleys (not included) can be found in a variety of outside diameters to fit this Taper-Lock bushing, enabling the precise selection of the amount of drive teeth or grooves. This bushing can be suitable for use in an array of mechanical and digital adjustable drives, including auto and printing industries.